Dry Ice and Soda Blasting Mold Removal in Clovis, CA
Dry ice or soda blasting removes mold from suitable exposed wood framing in your Clovis property. Call 24/7 to start your assessment and define the cleanup scope.
- Surface suitability checked
- Containment and HEPA dust control
- Moisture source assessed first
Dry Ice and Soda Blasting Mold Removal Services in Clovis
Accessible mold on your sound basement joists, attic rafters and exposed studs is included in cleanup. The wood's surface condition guides whether blasting is suitable.
CO2 pellets used for dry ice cleaning change into gas. Compressed air propels the media against your wood. Baking soda leaves material behind, requiring collection together with mold debris and dust.
Before work begins, your written work scope sets out cleaning, containment and removal, plus moisture corrections and rebuilding. Closed cavities remain beyond blasting's reach, and decayed structural timber still needs repair.
- Exposed Framing and Sheathing Condition Assessment
- Trying Dry Ice or Soda on Surfaces
- Contained cleaning with HEPA filtration
- Debris and spent media collection
- Drying and post-remediation verification
Dry Ice Surface Cleaning in Greater Fresno: Signs to Look For
Have visible mold on your exposed framing assessed. The signs below may point toward blasting as an option.
Growth Along Attic Rafters
Patches appear across potentially sound roof decking or exposed rafters.
Growth Exposed by Drywall Removal
Affected studs become visible inside an opened wall and require cleanup before finishes are replaced.
Mold Around Joist Corners
Ordinary wiping struggles with growth along uneven wood surfaces and joints.
Returning Basement Spots
Growth reappears on beams where water intrusion or moisture remains ongoing.
Your Dry Ice and Soda Cleaning Process in Clovis
After your assessment comes removal within containment, followed by cleaning, drying and verification.
Assess Wood and Access
Visible mold growth is mapped together with affected materials. A thermal imaging camera finds differences in temperature, not mold; a moisture meter measures dampness.
Define Moisture Corrections and Scope
Leaks are assessed alongside condensation ahead of cleaning. Your scope separates cleanup, moisture repairs and rebuilding.
Set Dry Ice Work Controls
Negative air pressure works alongside poly sheeting and HEPA filtration to contain dust. Before using dry ice, equipment protection, gas monitoring and ventilation are put in place.
Remove Unsalvageable Materials
Damaged drywall and insulation are bagged inside containment. Wood that has deteriorated needs a repair assessment.
Surface Trials for Dry Ice or Soda Blasting
A test area establishes media and settings before cleaning. When blasting does not suit sensitive surfaces, another method is assessed and used.
Collect Media and Debris
A HEPA vacuum collects removed growth and dust. Soda deposits are cleaned out of accessible recesses, whereas dry ice leaves no spent blasting material.
Dry and Finish Cleaning
When necessary, controlled air movers and a dehumidifier help surfaces dry. Progress is tracked through moisture readings ahead of final cleaning and assessment.
Verify Before Removing Containment
Moisture content is measured and cleanliness checked. Required checks precede containment removal, including clearance testing by an independent assessor when specified.
Your Choice for Dry Ice and Soda Blasting Mold Removal: Why Fresno Mold Removal Services?
Removal Through Final Checks
After blasting, debris is collected and drying and verification occur before containment is removed.
Calls Answered 24/7
To begin your framing cleanup anywhere across the metro, call one number at night or during the day.
Clear Scope and Contained Work
Work begins with surfaces and containment defined in your scope, along with HEPA filtration and media-specific controls.
Dry Ice Suitability Checked First
Your cleaning method depends on a surface trial and the condition of your wood.
What to Do Ahead of Dry Ice Cleaning in Fresno County
Do not disturb moldy framing; arrange your assessment by phone.
- Stop incoming water if safe. Avoid electrical equipment near wet areas.
- Keep people and pets away. Keep household activities outside the affected area.
- Leave growth in place. Containment must be ready before any sanding, blasting or brushing starts.
- Keep affected HVAC off. Avoid operating equipment you suspect contains mold, and never direct fans toward growth.
- Limit fresh water damage. Dry water-damaged areas along with affected items within 24 to 48 hours to prevent mold growth, as EPA advises.
Pricing Dry Ice and Soda Cleaning in Clovis
The scope assessed for your cleanup determines pricing. Units vary among these Fixr figures. Rates for general blasting are separate from total prices for mold remediation.
Dry ice treatment for mold
$1,400 to $2,000 per jobSource: Fixr, Mold Remediation Cost (checked 2026-10-23)Labor-inclusive general dry ice blasting, with no mold-specific pricing
Per square foot: $3.5 to $5Source: Fixr, Sandblasting Cost (dry ice blasting section, not mold specific) (checked 2026-10-23)General soda blasting, without mold-specific pricing
$45 to $75 per hourSource: Fixr, Sandblasting Cost (dry ice blasting section, not mold specific) (checked 2026-10-23)What Changes Your Dry Ice Mold Removal Cost?
- Separate repairs and removal of damaged materials
- Affected surface area and condition
- Attic or crawl space access
- Containment, ventilation and HEPA filtration
- Media, debris collection and disposal
What You Pay for Blasting and Cleanup
These published national ranges are planning figures. Your on-site assessment defines the work and price before cleanup starts, including any separate source repairs or rebuilding.
Call (844) 352-3560 about costDry Ice and Soda Blasting Mold Removal Service Area Across Greater Fresno
Call (844) 352-3560 to arrange cleanup in Clovis or nearby communities. One number covers the metro.
Dry Ice and Soda Blasting Mold Removal in Locations Near Clovis
What People Ask About Dry Ice and Soda Blasting Mold Removal in Clovis
Do you need testing ahead of or following dry ice cleaning?
Visible mold often does not need air sampling under EPA guidance. Moisture checks and inspection establish the area for cleanup. Following blasting, containment stays up until debris removal, drying and cleanliness have been checked. When specified, clearance testing is carried out by an independent assessor. There is no federal limit for mold levels indoors.
Will dry ice blasting replace damaged wood or drywall?
Blasting cleans suitable exposed surfaces; it does not replace damaged material. Moldy drywall and unsalvageable insulation may need removal to expose the framing. A repair assessment is needed for soft or rotting wood. Your scope separates surface cleaning from structural repairs, replacement insulation and finish work before cleanup begins.
Is staying home possible while blasting takes place?
Separation between occupied rooms, the workspace and the debris route may allow you to stay home. Shared ventilation and noise influence that decision alongside household needs and gas controls. Your assessment sets access limits ahead of the work. Some layouts require you to stay elsewhere until cleaning and required checks are complete.
How do dry ice and soda blasting differ?
Dry ice pellets turn to gas during cleaning, leaving removed contamination to collect. Soda blasting leaves debris together with the baking soda already used. Containment remains necessary for both methods, along with final cleanup. Method suitability for your wood, ventilation, access and intended finish is determined by a surface assessment and trial area.
What does blasting cleanup cost in Fresno County?
The price reflects your wood condition and access, plus the surface area and full extent of cleanup. Above, the sourced cards separate general blasting rates from mold treatment, preserving the different units for each. Your total can vary with containment, drying, ventilation and removal of materials. Work begins after your scope and pricing have been explained.
What is the timeline for dry ice cleanup in Clovis?
Assessment of your framing, moisture conditions and access route comes before scheduling. Narrow hatches, large surface areas and damaged insulation add work before blasting starts. After surface cleaning, debris is collected and drying follows. Containment removal and the start of repairs depend on agreed verification and moisture readings.
After wood blasting, could mold come back?
Mold may recur where the moisture issue has not been fixed. At the start of your cleanup, the moisture source is addressed and repairs needed alongside removal are identified. Sound wood is cleaned and dried before new finishes go in. Only repairs specified in your scope are included for roofing, plumbing or ventilation.
Dry Ice Cleanup and Insurance in California
Homeowners insurance coverage depends on moisture cause, exclusions, mold limits and deductible. Cleanup and repairs may receive different decisions.
Precautions for Your Dry Ice Work in California
Controls in your work plan address the chosen media's hazards as well as airborne debris.
Dry Ice Particle Control
Containment works with a HEPA air scrubber to curb the dispersal of dust and mold spores while blasting.
Worker Protection
For airborne debris, compressed air, cold media and noise, protective equipment is used.
Dry Ice Gas Controls
Carbon dioxide is released by dry ice. HEPA filtration cannot capture this gas; plans for your workspace include ventilation plus gas monitoring.
Surface Protection
The cleaning outcome is checked using a test area. Wiring and finishes, along with mechanical equipment, receive protection from the blasting stream.
Cleanup scope: Homeowner cleanup is often possible for areas below about 10 square feet, EPA says. This does not mean you should blast yourself. Mold from sewage or contaminated water, HVAC systems and larger areas require professional help.
Which Materials Are Cleaned During Dry Ice Work in Fresno County?
Damaged porous materials may require removal; you can often retain sound framing.
Wood surfaces
- Suitable joists and rafters, along with studs and sheathing, receive cleaning and drying following assessment.
Damaged porous materials
- Moldy drywall and unsalvageable insulation are removed. Repair needs of decayed structural wood require assessment.
Non-porous surfaces
- Adjacent glass and metal receive protection or cleaning with an appropriate method.
Planning the Timing of Dry Ice Cleanup in Fresno County
Preparation starts your schedule; final verification completes it.
- Access: Tight hatches and the paths for hoses influence setup.
- Material condition: Exposed decay can add repairs.
- Completion: Moisture readings help determine readiness to rebuild alongside final checks.
Moisture and Odor After Dry Ice Cleaning in Greater Fresno
Musty odor is investigated with moisture checks. Blasting cannot reach closed cavities; fragrance does not remove hidden growth.
EPA recommends indoor relative humidity below 60 percent, ideally 30 to 50 percent. Moisture control and completed leak repairs help prevent mold growth from returning.
Requirements for Your Dry Ice Work in California
Removal Requirements
California has no state license or certification for mold assessors or remediators, according to the California Department of Public Health. General construction work above a small dollar amount does need a license from the Contractors State License Board (CSLB), so it is worth checking a contractor's license there and asking about their mold training.
Repair Permits
Opening walls, replacing structural materials and other included building work determine which permits are required.
Rental Properties
Under California's housing law, visible mold found by a health officer or code enforcement officer can make a rental substandard. Renters can contact their local health or code enforcement department to ask for an inspection.
State Mold Information
The California Department of Public Health (CDPH) Air Quality Section publishes mold and dampness guidance and a mold FAQ. CDPH says visible mold, dampness, and mold odor are unhealthy and should be fixed, and that routine mold testing is not needed when mold is visible.
State guidance: CDPH Frequently Asked Questions about Mold; CDPH Statement on Building Dampness, Mold, and Health; California Health and Safety Code 26147 (leginfo); California Health and Safety Code 17920.3 (leginfo)
Related Services and Next Steps
Start Your Dry Ice and Soda Blasting Mold Removal in Clovis
Call 24/7 to arrange your assessment. Your cleanup starts with the affected surfaces, moisture source and access to your home.